Issue getting started - Printable Version +- StackAndTile Forums (https://www.stackandtile.com/forum) +-- Forum: General (https://www.stackandtile.com/forum/forumdisplay.php?fid=1) +--- Forum: Support Help (https://www.stackandtile.com/forum/forumdisplay.php?fid=2) +--- Thread: Issue getting started (/showthread.php?tid=208) |
Issue getting started - JonG19 - 11-16-2011 I have been trying to get SAT running for a couple hours now, and i'm still doing something wrong. I read all the beginner info in the help section, and followed the set-up instructions exactly. I was able to set up my grid/slots very easily, and was able to add Merge to my poker site list. I was able to press F7 to get SAT to recognize the table, and was able to press F10 to get a fold. Everything seemed fine to this point, until I actually tried to test it out. I loaded up a few tables, and nothing happened (yes I remembered to press start ). The tables do not move at all. They do not move to the stack, and they do not move to any of the slots when action is required. Hotkeys are also unresponsive. I tried different ones like "fold" and "stack table" and had no luck. It seems like the program isn't communicating with Merge correctly, and I can't figure out why. This really confused me, because like I said, I was able to use the fold hotkey when adding Merge to the site list. Does anyone have any suggestions for what the problem might be? FWIW I made sure to run the program as admin, and made sure to hit "start" on SAT before opening any tables. I assume there is some simple setting i've gotten wrong when setting it up lol. Thanks in advance! RE: Issue getting started - SaT_Admin - 11-16-2011 Can you post your configuration file? To do that, click on File->Current Layout, and copy and paste the whole file. I'll take a look RE: Issue getting started - JonG19 - 11-17-2011 Thank you for your help! I also wanted to mention that I'm using "normal mode" on Merge, so that's not the issue. [settings] table_width=765 table_height=574 total_slots=4 slot1x=0 slot1y=0 slot2x=516 slot2y=0 slot3x=0 slot3y=412 stack_slot=1 newtables_slot=grid move_on_street=preflop oldtables_duration=3 oldtables_slot=close scan_mode=PW slot4x=516 slot4y=411 [general] gui_x=425 gui_y=390 last_tab= [sites] Merge_included_executable_path=C:\Program Files\LockPoker\client.exe Merge_included_resized_table_width=765 Merge_included_resized_table_height=574 Merge_included_action_color=0x4f4f4f Merge_included_action_x_scaled=291 Merge_included_action_y_scaled=482 number_of_sites=1 included_sites=Merge [hotkeys] number_of_hotkeys=1 hotkey1action=Fold + Stack table hotkey1key=Z send_table_under_mouse=1 RE: Issue getting started - SaT_Admin - 11-17-2011 Ok, here is what SHOULD happen, based on your config: When you press Start, tables should start filling up your grid slots 2, 3, and 4 (this is the New Tables=grid setting). Then, you only have one hotkey set up, Z, so you can mouseover each table and press Z, and the tables should return to the stack. Then, once they are in the stack, when it is your turn to act, they should start filling the grid again. However, if you say that SaT is unresponsive and none of the above works, then there is a major problem. I would suggest running SaT as admin, but you've already done that too. If its still not working, send me a PM with your skype name and I'll take a look. |