Eurobet Poker
#1
Hello. I don't know if I'm doing well but I'm following the steps to add a new site, more precisely it's an IpokerNew one. I tried to add by myself but later I saw that you can add it if I send you the message that sends me the software doing the Diagnostic. This is the message:

title=[Eurobet Poker],class=[Qt5QWindowOwnDCIcon],pid=[10496]

I hope that you can help me and others with same problem. Thank you
Reply
#2
Please download this version v2.98.07f and let me know if it works:

http://www.stackandtile.com/sat/tmp/Stac...29807f.exe
Reply
#3
(09-17-2019, 03:30 AM)EnRgizer Wrote: Hello. I don't know if I'm doing well but I'm following the steps to add a new site, more precisely it's an IpokerNew one. I tried to add by myself but later I saw that you can add it if I send you the message that sends me the software doing the Diagnostic. This is the message:

title=[Eurobet Poker],class=[Qt5QWindowOwnDCIcon],pid=[10496]

I hope that you can help me and others with same problem. Thank you

(09-17-2019, 10:43 AM)SaT_Admin Wrote: Please download this version v2.98.07f and let me know if it works:

http://www.stackandtile.com/sat/tmp/Stac...29807f.exe


Yes perfect, now it's all right. Thank you very much!!!
Reply
#4
Hello. Excuse me, I noticed now that tables are resized but don't move in the grid when the hand is over like I put on other sites. I changed all settings as showed in supported sites section for IPoker but nothing.
Reply
#5
(09-18-2019, 11:32 PM)EnRgizer Wrote: Hello. Excuse me, I noticed now that tables are resized but don't move in the grid when the hand is over like I put on other sites. I changed all settings as showed in supported sites section for IPoker but nothing.

Do you mean the tables don't move back to the STACK when the hand is over? If you are using that advanced option setting, then you need to take into consideration these issues:

https://www.stackandtile.com/sat/help/preferred-seating
https://www.stackandtile.com/sat/help/fl...-hole-card
Reply
#6
Ok, now I removed it and add one time more paying attention to the white area of cards. Now tables try to move to stack but immediately come back to the original position and don't disappear unless I reduced them to icon.
Reply
#7
Does the same thing happen if you set up a "Stack Table" hotkey and try to move the table to the stack that way? The table will immediately come back into the grid?

If so, that would mean that SaT is thinking that the table always requires action. There could be a few reasons why this is happening. How many monitors do you have? And are they different sizes and scaling? And what version of Windows?

You can run through this Test and some of the solutions. Let me know what you find:

https://www.stackandtile.com/sat/help/ta...ncorrectly
Reply
#8
No I don't have more monitors and I have Win10. I don't know, I tried all but I have always same problem, proved by the testing that shows me NO when I have to act, and YES when I don't have. And moreover I have same problem with 888. Only with these two sites.
Reply
#9
Can you leave me your skype name? Then I can contact you and set up a teamviewer session
Reply
#10
Ok perfect.

dandy928

https://join.skype.com/invite/GrwYZ8y1BWtx
Reply


[-]
Quick Reply
Message
Type your reply to this message here.

Username::
Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)
Please select the number: 9
1 2 3 4 5 6 7 8 9 10